All Deap Sea Products |
|
|
|
|
|
| The DSE560 is an Automatic Engine Control Module. The module is used to automatically start and stop the engine and indicate operational status and fault conditions. It will automatically shut down the engine and indicate the engine failure by means of a graphical LCD display and a flashing LED on the front panel. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The DSE808 PC Software Configuration Interface is designed to allow the user to acess the configuration stored within the module, enabling changes to be made to the settings. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The DSE Multi-set communications package allows single screen, single connection monitoring of an entire generating set system. Up to six generators can be monitored at a time and if required a DSE556 Mains Controller ATS Module can be part of the system. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The DSE512 is a Manual Engine Control Module designed to allow the OEM to meet demand for increased capability within the industry. The module is used to start and stop the engine, indicating the operational status and fault conditions, automatically shutting down the engine and indicating the engine failure by means of a flashing LED. THIS PRODUCT IS NOW OBSOLETE. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The DSE4210 is now an obsolete product. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The DSE5103 is a 3 Amp 12/24 Volt Battery Charger. It is designed to be permanently connected to automotive batteries, maintaining them in a fully charged condition without overcharging. The charger is also capable of rapidly recharging batteries at a current up to the full rated output. The charger may also be used to supply a standing load attached to the battery. The charger output may be factory set to account for the standing load. THIS PRODUCT IS OBSOLETE. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The DSE5105 is a 5 Amp 12/24 Volt Battery Charger. It is designed to be permanently connected to automotive batteries, maintaining them in a fully charged condition without overcharging. The charger is also capable of rapidly recharging batteries at a current up to the full rated output. The charger may also be used to supply a standing load attached to the battery. The charger output may be factory set to account for the standing load. THIS PRODUCT IS OBSOLETE. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The DSE5110 BC is a 10 Amp battery charger designed for permanent connection to automotive batteries, maintaining them in a fully charged condition without overcharging. The charger is capable of rapidly recharging the batteries at a current up to the full rated output. The charger may also be used to supply a standing load attached to the battery and output may be factory set to account for the standing load. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The charger has been designed to be permanently connected to automotive batteries, keeping them charged to their maximum capacity. The chargers can also be used to supply a standing load that is attached to a battery. To improve reliability the chargers do not include any moving parts. The technology inside the chargers has been designed to avoid overcharging and overloading. The chargers will also continue to operate during cranking and running and have the ability to accept multiple AC voltage connections. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| Lightweight Compact design Can remain operational during engine cranking and running
Suitable for connection to a wide range of AC voltages between 100V and 240V, 50Hz or 60Hz.
No moving parts Switch mode design Overload & short circuit protection LED charging indicator
Convection cooling Minimum 80% efficiency throughout full operating range
...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
|
|
|
|
| The 3.7 Amp Battery Charger has been designed to be permanently connected to batteries, keeping them charged to their maximum capacity. The charger can be either mounted via DIN Rail or to the Chassis, using the fixing holes that are built into the case. The chargers stylish design includes an LED indicator on the front that shows when the charger is in a normal or overload condition. ...Continue >> |
| |
|
|
|
| Not available in stock
|
|
|
View Cart
Hablamos Español 
